Search
Menu
My Account
Loading...
main product photo

Hot Spring Vanishing Act Hot Tub Calcium Remover

Rating:
92% of 100
2 Reviews Add Your Review
£49.99
In stock
SKU
hotspring_vanishingact
  • Hot Tub Calcium Hardness Remover
  • A simple way to reduce the calcium hardness level in your hot tub
  • Simply rinse through, drop in over your drain or suction, flip after 12 hours and then remove 12 hours later
  • Made by Hot Spring, perfect for the Freshwater Salt system or ACE system. 
 
Order by 3pm for FREE UK Next Working Day Delivery on this item and all chemicals/accessories with no minimum spend!
See Delivery Info and T&Cs

A simple, fast, and easy way to enjoy a soft water feel in a hot tub without the costly expense and without having to drain the hot tub. Place Vanishing Act on the bottom drain of your hot tub or near your hot tub suction when you refill it. Turn over the bag after 12 hours. 12 hours later throw out the bag. Simple, easy, and effective.

Create a softer, more enjoyable soaking experience. Help prolong the life of your hot tub and extend the amount of time between water changes. 

Looking for a more cost effective way to soften water? Check out the On The Go Portable Water Softener

Related Posts
  1. A Guide to Calcium Hardness in Your Hot Tub
Product Questions (1)
Customer Questions
Can this be used with an inflatable hot tub? We have very hard water in our area and not sure how best to combat that. Thanks!
This would not be overly effective in an inflatable spa. To prevent scaling issues, keep you PH 7.2 to 7.6 and you could use an anti-scale product weekly as a belt and braces approach. It may also be worth looking at a conditioner like o-care or Silk...
Please, mind that only logged in users can submit questions
Directions for use
  1. After filling your hot tub, use a test strip to measure the hardness level of the water. If hardness is above 100ppm, use Vanishing Act calcium remover to soften the water. Suggested hardness level is 75ppm to 150ppm (25-75ppm for Salt Systems).
  2. Rinse the Vanishing Act calcium remover with running water until the water runs clear. When placed in the hot tub, slight colour transfer to the water may occur ancd can be easily resolved with chlorine.

For Hot Tubs with a heater return (No Bypass Filtration / No Suctions):

  1. Place the Vanishing Act calcium remover (flat side down) over the heater return in the footwell.
  2. After 10-12 hours, slip the calcium remover and re-position over the heater return grill.
  3. After a total of 24 hours, take the calcium remover off of the heater return and discard. 
  4. DO NOT RUN THE JETS WHILE CALCIUM REMOVER IS IN PLACE.

For Hot Tubs with jet suction fittings:

  1. Activate the low speed jet pump or press the Vanishing Act button on your control panel if so equipped.
  2. Place the Vanishing Act calcium remover completely over the associated suction fitting in the footwell (Check manual of your Hot Spring Spa if unsure).
  3. Test spa water for hardness after jets shut off, which may take 1-2 hours. Repeat 1-2 times to achieve suggested hardness level of 75ppm-100ppm (25-75ppm for Salt Systems) then discard the calcium remover. A single 6 hour Soft Water cycle is typically adequate. 

Important:

  • Always make sure your hot tub water is properly balanced with a sanitiser like chlorine or Bromine before entering your hot tub.
  • For maximum effectiveness, esnure that the calcium remover remains on the heater return or suction fitting while the calcium remover is in use.
  • Calcium remover may not be necessary if water hardness is already in or below the suggested range.
  • Multiple calcium removers may be needed if the water hardness is above 200ppm. 
Customer Reviews Write a Review
Write Your Own Review
Please Sign in or create an account to leave a review for this product.
We found other products you might like!